LED防爆燈具生產廠家工藝要求，20W,30W,40W,50W,60W,70W,80W,90W,100WLED防爆燈生產要求，防爆燈具生產要求
LED防爆燈具生產廠家工藝要求對于隔爆型燈具，隔爆外殼是這類隔爆型防爆電氣設備的關鍵部件，所以隔爆外殼必須符合一般要求和隔爆性能的特殊要求。
1．一般要求
隔爆型燈具是一種特殊的燈具，防爆泛光燈必須符合普通燈具的通用要求。
1．1 燈具的外殼造型力求美觀大方，結構緊湊可靠，輕便且工藝性要好。
1．2 要求有足夠的容積用來放置燈座、燈泡、反射器、接線柱等電氣元件和燈具配件，同時要考慮布局的合理性，便于安裝、更換光源等使用和維修。
1．3 要有一定表面積的透明部分，以使燈具內部光源的光通量通過反射部件有效地投射出來。
1．4 要綜合考慮散熱、防塵、防水和防腐等措施，在結構上給予充分的保證。
1．5 在適當的位置，合理地布置內外接地，并有相應的性接地標志。
2．特殊要求
隔爆外殼國家防爆標準要求能承受內部爆炸性氣體混合物的爆炸壓力，并阻止內部的爆炸火焰向外殼周圍爆炸性混合物傳播；防爆泛光燈要滿足這—性能，就必須具體考慮如下特殊要求：
2．1 耐爆性能。要求燈具外殼有足夠的強度和剛度來承受燈具內腔可能引起的爆炸壓力，因此要選擇適當的材質和壁厚，組成*佳的立體幾何形狀分布，這種腔體結構， 既要美觀大方，又要盡可能地避免形體變化過大所造成的應力不均，以便確保*終能夠通過GB3836．2規定的動態強度試驗。
2．2 隔爆功能。燈具的隔爆外殼在設計時就必須嚴格按照GB3836．2的規定選用適當的隔爆接合面結構參數、引入裝置的方式，透明件與燈體部件的密封結構形 式、隔爆接合面的粗糙度，隔爆螺紋的精度等，以便有效地阻止內部爆炸火焰向外殼周圍爆炸性混合物傳播，*終通過GB3836．2規定的隔爆性能試驗。
2．3 燈具的隔爆外殼，多數是由2個或多個連通空腔組成，往往很容易產生壓力重疊現象，一般來說，防爆泛光燈這將會造成爆炸壓力異常急劇上升而超過預計的*大壓 力。為此應盡量增大聯通孔面積，使外殼內部的形狀能消除壓力重疊現象。如果實際不能消除壓力重疊現象，則應在腔與腔之間采取隔爆措施，消除壓力重疊。
2．4 對于ⅡC的隔爆型燈具，GB3836．2嚴格規定不應采用爆炸時隔爆間隙趨向增大的平面隔爆接合面，為此，目前我國的隔爆型ⅡC防爆燈具大多數采用隔爆螺紋的結構形式，以便燈具更換光源或維修時燈具腔體能順利開啟。
For critical components flameproof lighting, flameproof enclosure is explosion-proof electrical equipment such , it is flameproof enclosure must meet the general requirements and the special requirements of explosion-proof performance .
1 . General requirements
Flameproof lighting is a special lighting, explosion-proof floodlight must meet the general requirements for ordinary lamps .
1.1 lamp shell shape seeks nice , compact structure, reliable, lightweight and better manufacturability .
1.2 requires sufficient volume to place the lamp, bulbs, reflectors , terminals and other electrical components and lighting accessories, taking into account the reasonableness of the layout , ease of installation, use and maintenance , such as replacing the light source .
1.3 have a transparent portion of the surface area , so that the light flux reflected by the light source inside the lamp member projecting out effectively .
1.4 takes into consideration the heat, dust, water and corrosion and other measures to give sufficient guarantees on the structure.
1.5 in place , reasonable layout inside and outside the ground , and a corresponding permanent ground sign.
2 . Special requirements
Explosion -proof enclosure national standards to withstａnd an internal explosion of an explosive gas mixture pressure and prevent internal explosion of an explosive mixture of flame spread to surrounding housing ; proof floodlight to meet this - performance , it must specifically consider the following specific requirements:
2.1 explosion -resistant properties. Lamp housing requires sufficient strength and rigidity to withstａnd the lamp lumen pressure may cause an explosion , so to select the appropriate material and wall thickness , composed of the best three-dimensional geometry of the distribution of this cavity structure , both nice, but also as far as possible to avoid overstressing the big physical changes caused by uneven dynamic strength testing to ensure the final through GB3836.2 regulations.
2.2 Explosion-proof function. Lamps designed flameproof enclosure must be strict selection of appropriate structural parameters in accordance with the provisions of flameproof joints GB3836.2 , the introduction of the device the way , in the form of sealed structure transparent parts and lamp body parts , flameproof joints roughness precision threaded explosion , in order to effectively prevent internal explosion of an explosive mixture of flame propagation around the housing , the final proof performance test prescribed by GB3836.2 .
2.3 lamps flameproof enclosure , the majority is composed of two or more communicating cavities composition, often very prone to stress overlap , in general , this will cause abnormal proof floodlight sharp rise more than expected explosion pressure maximum pressure. To this end Unicom hole area should be increased , so that the shape of the pressure inside the enclosure to eliminate duplication . If the actual pressure not eliminate duplication , proof measures should be taken between the chamber and the chamber pressure to eliminate overlap .
2.4 For Ⅱ C flameproof lighting , GB3836.2 strict rules should not be used flameproof gap tends to increase when the plane explosion proof joints , for which China's current flameproof explosion-proof lighting in most cases, Ⅱ C compartment explosion in the form of thread structure to replace the lamp when the lamp lumen maintenance light or physical well open .
LED防爆燈具生產廠家工藝要求，同所有防爆燈具生產一樣的原理
